The Beginners Guide to using the Computer
By: Robert Beers
Booting from another devise on start up
Step 1. Start or restart your computer.
Step 2. You will need to read when the computer starts to find the correct key to
push. All computers are different.
Step 3. If you choose the Bios then go to the Boot Options and choose what you
want to boot from.
Step 4. If you chose to pick from the quick boot then just pick what you want to
boot from.
Warning: I recommend anyone who does not know anything
about computers to choose from the Quick Boot options. Messing
around in the bios can destroy your computer.
Starting in safe mode
Safe Mode is a version of windows were nothing is running. You use Safe
Mode when you have a virus that is causing your virus software to not work, or you
can not do a system restore.
Step 1. Start or Restart your computer.
Step 2. To get in to Safe Mode press the F8 key at the top of your keyboard.
Step 3. It will give you options of how you would like to start Safe Mode. You can
run it with Network enabled or disabled.
Speed up your computers start up
If your computer takes forever to boot that may mean that you have to much
starting up. All of the programs that are set to start up when you turn your
computer
on eats up RAM and can slow your computer down a lot. Follow these
steps to stop all the unnecessary programs from booting when your
computer start.
Step 1. Go down to your start menu button. It is located at the bottom left hand
corner.
Step 2. When the start menu opens, look for the Run icon and push it.
Step 3. A window will open with a blank line. In that line you will type msconfig,
then push OK.
Step 4. Now the System Configuration Utility window has opened. You will go to
the Tab called Start up. You will see a bunch of programs in there, that are
checked. Those are the Programs that are starting when windows does.
Step 5. Look through the list of Start Up items. It is safe for you to uncheck any
program that begins with C:\ProgramFiles\. Just remember that if you are
running virus, windows defender, or any other protection software it may
begin with Program Files.
Step 6. Uncheck any of the Program Files you wish to stop starting up.
Step 7. When you have unchecked the program that you want to stop starting up
press OK. It will ask if you would like to restart your computer. You do not
have to but it is recommended that you do right away.
Step 8. When your computer restarts the next time, you will get this message “You
have changed your Start Up Configurations” Don't be alarmed! All you
need to do is check the box that says “Don't show this message or launch
System Configurations when windows restarts.”
Automatic Windows Updates
It
is very important that you have your Automatic Updates activated. Your
computer gets critical updates from Microsoft this helps your computers
security from attackers. Here are the steps to be sure that it is
activated or that you activate it.
Step 1. You will need to go to the Start menu.
Step 2. Once the start menu comes up, look for the link called Control Panels. Click
that.
Step 3. Click on the Security Center link.
Step 4. Look for the link called Automatic Updates. Then click it.
Step 5. Make sure the circle or box next to Automatic is checked. Makes sure it is
set to download updates everyday and you pick the time that’s best for you.
Step 6. Press OK. Your done setting up your Automatic Updates!
Download Windows Updates Manually
You can also download the updates manually. When you do this you can
also update more than just critical updates. You have three options.
Critical updates, Hardware, and Software updates. Follow these steps to
update your computer manually.
Step 1. Go to www.update.microsoft.com
Step 2. If this is your first time, you may need to install ActiveX. The site will tell
you and walk you through how.
Step 3. Once it loads click the button that says Custom. Now it will search your
computer for any updates needed.
Step 4. On the left hand side there is 3 choices. High Priority, Software Optional,
Hardware Optional. You can install all the updates from them all.
Step 5. Once you have selected all the updates you wish to install, press Review and
Install. You may have to restart your computer after they Install.
Activating Windows Firewall
It is important that you activate your Windows built in Firewall. The
firewall helps to protect your computer from Viruses and some attack
attempts. Here are steps to be sure your Firewall is active.
Step 1. Go to your Start Menu. Click it.
Step 2. Go to the Control Panel Link. Click on it.
Step 3. Click on the Security Center Icon in Control Panels.
Step 4. Go down to the Icon labeled Windows Firewall. Click that.
Step 5. Check to be sure that the box is checked Next to ON. If not check it.
Step 6. Press OK. You have now activated your Windows Firewall.
Adding or Removing Programs
This is used so you do not have to look for the uninstall for a
program. You can remove all unused program so that you can clear space
for new ones. To use the Adding or Removing programs just follow these
steps.
Step 1. Click on your Start Menu.
Step 2. In the Start Menu find and click on Control Panels.
Step 3. When Control Panels opens find the Add or Remove Programs link. Click
that.
Step 4. Look through the list of programs. If you see one you want to get rid of then
click it.
Step 5. Now that you have highlighted a program to get rid of look for the
Change/Remove Button. Click that.
Step 6. Repeat steps 4 and 5 until you are done. Now Restart your computer and
your done.
Disk Cleanup
Disk Cleanups main purpose it to clean the temporary files that your
computer saves. It can also empty your recycling bin for you if you
haven’t done so. These steps will walk you through on how to use the
Disk Cleanup.
Step 1. You will need to find your My Computer Icon. If it is not on your desktop
then you will need to go to you start menu and open it that way or press the
windows key + E.
Step 2. Go down to the drive you wish to clean. Most people only clean drive C.
Now right Click it.
Step 3. Now a menu should have opened when you right clicked on the drive. Go to
the Properties which should be the last choice.
Step 4. Now a window should have opened. Look at the top it should be in the
General Tab. You should be able to see a Pie Chart, that is your Hard Drive
usage. Now look for the Button that says Disk Cleanup. Push that Button.
Step 5. When the window called Disk Cleanup comes up you notice a bunch or stuff
that you can select. Choose what you want to be cleaned up.
Step 6. Once you have selected everything you want to be cleaned press the OK
Button and let it erase all that stuff.
Defragging your computer
Though
time you have added and deleted stuff from the computer. This causes
your files to become Defraged. When I say Defraged I mean it moves pars
of files all over the place causing your computer to have to work harder
to start programs. When your computer has to work harder it eats up
more RAM causing your computer to slow down. I recommend that you Defrag
your computer at least once a month or after you do a mass delete of
stuff. To run the Defrag program follow these steps.
Step 1. Locate the My Computer Icon. If it is not located on your desktop you will
need to go to your Start Menu and open it from there or press the windows
key + E.
Step 2. Now that you have opened My Computer you now need to Right Click
Drive C, or what ever drive you are trying to Defrag.
Step 3. After Right Clicking you need to go to the option that says Properties
Should be the last option.
Step 4. The properties window should have opened. You should be in the general
Tab, right next to were it says General you see the Tools Tab Push that.
Step 5. In tools you see 3 options look for the one that says Disk Defragmentor.
Click it.
Step 6. The Disk Defragmentor should have opened. Go down to the bottom, you
should see two options Analyze and Defragment. You need to pus the
Defragment Button.
Step 7. Disk Defraging will take a while to complete. So I Recommend you do this
when you don’t need the computer.
Scan Your Disk for Errors
From time to time windows files go corrupt and causes your computer to
crash and or slow down. The best thing about that is Microsoft has
included a scan disk program in windows. The scan disk program can fix
many errors but as everything it can not repair everything. Follow these
steps so that you can check your computer for any errors so you can
correct them before its to late.
Step 1. You need to find the My Computer Icon. If not on the desktop you will need
to go to your Start Menu and open it that way or you can press the windows
key + E at the same time.
Step 2. Once you open My Computer you will need to go down to the Drive you
would like to check, most likely it will be C. Right click the Drive and go to
properties.
Step 3. You will notice that it opened up in General. You will need to select the Tools
Tab next to General.
Step 4. The first of the 3 options is the one you will select. Before you do check to be
sure its the Error Checking one. If it is click the button.
Step 5. You have now entered the Error checker you will notice there is 2
unchecked boxes you need to check them both. Once you have check them
press Start.
Step 6. Don’t be alarmed when it ask you if you would like to schedule the scan for
the next time you start Windows. Select yes for that option then press OK.
Restart your computer and let it scan it will take a while.
System Restore
System Restore is used to restore your computer back to an earlier
working Stage. You would want to use system restore if you have been
having a lot of errors. Just because it restores your computer back to
an earlier time doesn’t mean it is going to delete your save programs
and personal stuff. There are two ways you can access System Restore.
Follow these steps.
Step 1. The First way to start system restore is to press F11 when the computer is
just starting up when u just turn it on or restart.
Step 2. The Second way to do a System Restore can be done in both Safe Mode and
in a Normal windows boot.
Step 3. In the start menu go to Control Panels.
Step 4. When the Control Panels window opens Press the System and Maintenance
Link.
Step 5. On the left hand side you should see options under See Also that says
System Restore. Click the link and follow Restores Directions.
User Accounts
You
would use User Accounts to create a new account for someone or to
update an existing account. You can add log in passwords for each
individual account. You use this to set the user account privileges. It
is best to have your administrator account separate from your everyday
use account. Only use your administrator account when you are installing
new programs, not being in your admin account helps to prevent viruses
from changing your registry files. To locate the User Account menu
follow these steps.
Step 1. Click on the Start Menu Button.
Step 2. When the Start Menu opens, find the icon named Control Panels. Click
that.
Step 3. Once Control Panels opens, look for the User Account icon. Click that. Now
set up your accounts.
Create a new Folder
You
would create a new folder to place documents and other icons you wish
to put in a place to keep them organized. Most people create folders on
their desktops so that it does not look like a mess. To create a folder
follow these steps.
Step 1. Right Click anywhere on your desktop.
Step 2. A set of options will appear. Select the option that says new, it will open a
new set of options.
Step 3. In the new set of options that just opened you need to look for the option
that says folder. Once you have found that click that option.
Step 4. A new folder should have appeared on your desktop. If the name is
highlighted push the delete key or Backspace and type in the new name you
wish to call it. If it is not highlighted please refer to step 5.
Step 5. Use this Step if your folder is highlighted or you wish to rename another file
then you will need to right click the file and go to the Rename option.
Create a Shortcut
You can create a Shortcut on your desktop. Shortcuts are used so that
you have easy access to your favorite websites or even your favorite
programs you use. To create a shortcut follow these easy steps.
Step 1. Right click anywhere on your desktop.
Step 2. Notice the options menu that popped up. Look for the option that says New.
Step 3. You should have moved your mouse down to the New option, A new window
of options should have opened next to the options that are open. Now look
for the option that says Shortcut. Click that option.
Step 4. A new window should have opened with a bar you can type your favorite
web address in or an option for browse. Here is an example of a web
address you can type in, www.updates.microsoft.com you would push next
after you entered that and it would ask for a name for the new short cut.
The name I would give this example would be Microsoft Updates.
Step 5. To add your favorite program you would press Browse instead of type
where you put the web address. Once you found your program you would
then follow the rest of Step 4's instructions.
Set your Screen Saver
Here are the steps to setting your screen saver.
Step 1. Right Click anywhere on the desktop.
Step 2. When the little pop up option window appears find the properties option.
Click that.
Step 3. The Display Properties Window will open. Look at the different Tabs at the
top of the window. It should have opened in the Themes Tab, now look for
the Tab called Screen Savers. Click that Tab.
Step 4. You are now in the Screen Saver Options. In these options you will be able
to tell your computer how long it has to be idle before the screen saver can
activate and you can choose your screen saver.
Step 5. Once you have set the screen saver to what you want. Select OK so that it
will save your options and exit.
Set your Desktop Background
Windows allows you to choose what you would like your background to be.
There are 2 different ways that you can set your Desktop Background.
Here are the steps to choosing your Background.
Step 1. If you are on a website and really like a picture and want it as your Desktop
Background here is how you can do that. Right click the picture.
Step 2. A menu option will appear, Look for the option Set as Background or Set as
Desktop Background. Push that.
Step 3. The second way to set a Desktop Background is. Right click anywhere on
your Desktop.
Step 4. The option window will appear. Find Properties then Click that.
Step 5. An properties window should have opened. Look at the Tabs at the top.
Find the one that say Desktop. Once you have found that push it.
Step 6. You are now in the Desktop Background options. In these options you can
choose a preloaded desktop Background or choose from the Pictures you
have in My Pictures. If you have more pictures some where else you will
have to push the Browse option.
Step 7. Now you can choose from the 3 options on the page for how you want the
picture displayed. They are Center, Tile, or Stretch. Choose your option
then press OK.
Internet Explorer Content Adviser
You would use this to block sites that you find unsuitable for people
to view. This can be used to keep children out of chat sites and even
pornographic websites. After you activate the Content Adviser you will
be prompted to set an administrator password. This password is so that
if you ever want to change settings or view a blocked web page you can
override the blocker. Here are the steps to setting it up.
Step 1. Open your Internet Explorer Web Browser.
Step 2. Find the option that says tools. Located at the top.
Step 3. When the tools option opens you will need to find the internet options link.
Push that.
Step 4. When the Internet Options opens you will see that there are 7 different tabs
at the top. Find the Content Tab and push it.
Step 5. Now that you are in the Content options find the Content Adviser activation
button. Push it.
Step 6. You have now enabled your content adviser. As a default setting everything
is blocked now. To unblock the websites you wish to allow you will need to
go though each of the different content things and move the Bar to the
right. That makes it so you can unblock certain sites.
Internet Explorer Content Adviser
Step 7. Once you have set the Content you wish to allow you need to press OK.
Step 8. Now you will be asked to create a password and hint. This is so if you wish
to change or shut off the Content Adviser or Allow a website to be viewed
all you will have to do is enter the password.
Virus Protection
In
today’s day in age virus protection is a must. You can spend a good
amount of money on virus protection, but why do that when there is a
free on that works real well. Here are the steps in downloading the free
virus protection.
Step 1. Go to the web page www.avira.com.
Step 2. Once you get on to the web page look on the left of the page for Downloads.
Step 3. OK now you have clicked Downloads. You should see the words Desktop
with some links under it. Find the link called “Avira AntiVir Personal- Free
Anti Virus.” Once you have found that Click the link.
Step 4. A new web page should have opened. Click the Green Download Now
Button.
Step 5. That will open up yet again a new web page. Where you will need to click on
the Download now Button again.
Step 6. If a yellow security warning pops down from the top of the web page just
under the tab, you need to click it and push the Download now button to
begin the download.
Step 7. Now a window should pop up giving you the option to Run or Save the
download. If you just want to run the file it will download the needed files so
that it can install. If you would like to save the file press save a new window
will pop up letting you pick the location to save the file. It is always best to
have a folder to were you save all your downloads to, or just save it to your
Virus Protection
Step 7. desktop. This is just so you can find the file.
Step 8. Once the file completes downloading click the run button and follow the
install directions.
Configure Avira Anti-virus
This is only if you have downloaded and installed the free Avira Anti-virus.
Step 1. Once the Virus software is installed the main window should pop up. If the
window does not pop up then you need to find the Red umbrella icon and
double click it. It may also be in a small icon down by the clock in the right
hand corner.
Step 2. Once the main menu is opened make sure all the options in the center of the
screen all have Green checks next to them. If you need to update the virus
definitions do so by clicking the start update button on the right side of the
screen.
Step 3. To configure the virus scanner to do a system scan at a certain time you
need to find the Administration button on the left hand side.
Step 4. Now you have two options after you clicked Administration find the one
that says scheduler and click it.
Step 5. To enable the scheduler you need to check the box under enabled.
Step 6. Now you need to right click on the job. A gray window should pop up. Find
where it says edit job and select that.
Step 7. Push next until you get to the Time of Job option. This is were your going to
pick the time you wish the scan to happen and how often it need to scan.
Step 8. Now push next until you get to the Finished Button after you push that your
done.
Repair for the dreaded blue screen of death
PC
users, you all know what it is: That dreaded Blue Screen of Death.
That's right, the BSOD. You've installed a seemingly innocent
application, restarted your computer, and suddenly you see this horror
in front of your eyes: A big blue screen with some cryptic message on
it. Try restarting again, same thing. You're dead. What will you do?
What WILL you do?? Well, don't let it ruin your day. Remain calm. If
you're using Windows XP, I can help you fix it. Come with me, down into
the bowels of Windows XP, where only the high priests go. It'll be fun!
I'm
going to show you how to bring your computer back to life, and restore
it to the point where things went south. You might want to print this
article and squirrel it away for that fateful day when this happens to
you. Or if you don't want to print it (and who prints anything these
days, anyway?), and you get a big ugly blue screen, just get on another
computer somewhere and come back to this Web page for comfort and
advice. I can get you out of this mess. I know, because I was in the
same mess and I got myself out of it.
Here's what to do:
First, get the Windows XP CD you used to install your operating system.
By the way, this routine only works with Windows XP, either
Professional or XP Home Edition. If you don't have a bootable XP CD, get
one and have it with you at all times, because you never know when the
dreaded BSOD might strike.
But before you do anything with
that CD, try restarting your computer again. Sometimes, for some odd
reason, this works. Usually not, though. If you've tried that and
everything else you can think of, and you can't even boot into Safe
Mode, this is the mission for you.
Put the XP CD in the drive, and restart. When it says "press any key to boot from CD," go ahead, press any key and you're on your way to recovery.
Press
F6 if you have Raid Drives and later select ‘S’ and place your Raid
driver in the ‘A’ Drive. Select your Driver for the list and then press
Enter. After installation press Enter to continue.
The
Recovery Console, that is. If it doesn't give you a choice to boot from
your CD drive, go into your computer's BIOS and make the adjustment for
it to boot from CD. PCs brands and motherboards are too diverse for me
to give you specifics on this, so follow the prompts and you can make
that CD boot happen without too much trouble. Look at your screen when
it boots up, and it always says "hit DEL for BIOS settings" or something
similar. If you can't get it to boot from CD, just give up and call for
support or take your computer to the nearest computer store for
professional help.
OK, troops, are you still with me?
Good. It'll look like you're re-installing Windows XP, but don't worry,
you're not. This is just a screen showing you that your computer is
loading enough files from the CD to actually do something, anything but
that awful blue screen.
Now when you see the screen that asks
you if you want to install Windows, don't! Just hit R for recover, and
you'll see the ominous Recovery Console. Don't let that
intimidate you; the Recovery Console is your ugly, black-suited friend.
It will have a dark, bleak screen, with the following stuff:
Microsoft Windows(R) Recovery Console
The Recovery Console provides system repair and recovery functionality.
Type EXIT to quit the Recovery Console and restart the computer.
1: C:\WINDOWS
Which Windows Installation would you like to log onto
(To cancel, press ENTER)?
Go
ahead and hit the number 1 on your keyboard, or whichever number
corresponds to the operating system you were using when havoc struck.
Enter your administrator password, and then hit enter. You're in! Now it's time to run with the big dogs! Do not be afraid, dear reader, I am here to help you.
If
you type the following commands into your computer, it will work magic,
akin to going back in time. There are three parts to this process, but
believe me, they take much less time than reinstalling Windows XP and
all your applications. So follow along with me, and keep in mind that
each command must be typed exactly as you see it here. Please note that
this procedure assumes that Windows XP is installed to the C:\Windows
folder. Make sure to change C:\Windows to the appropriate windows folder
if it's at a different location. The copy commands will answer you with
a little "file copied" message. The delete commands just move on to the
next line. Because of the way your Web browser displays individual
lines, a command might look to you like it's two lines, so I've
separated each command by an empty line. But anyway, type the whole
command in one line, and when you've finished typing that command, hit
the Enter key. Be sure to include the spaces I've included between each
word here:
md tmp
copy C:\windows\system32\config\system C:\windows\tmp\system.bak
copy C:\windows\system32\config\software C:\windows\tmp\software.bak
copy C:\windows\system32\config\sam C:\windows\tmp\sam.bak
copy C:\windows\system32\config\security C:\windows\tmp\security.bak
copy C:\windows\system32\config\default C:\windows\tmp\default.bak
delete C:\windows\system32\config\system
delete C:\windows\system32\config\software
delete C:\windows\system32\config\Sam
delete C:\windows\system32\config\security
delete C:\windows\system32\config\default
copy C:\windows\repair\system C:\windows\system32\config\system
copy C:\windows\repair\software C:\windows\system32\config\software
copy C:\windows\repair\sam C:\windows\system32\config\sam
copy C:\windows\repair\security C:\windows\system32\config\security
copy C:\windows\repair\default C:\windows\system32\config\default
Now
you can relax for a minute. You've made it through the first part! Way
to go! Now what did you just do? I'll tell you. You first made a
temporary directory called "tmp" (md tmp), and then into it, you copied
all the files that boot up Windows. Then you deleted all those startup
files, one of which is the stinker that got you into this mess in the
first place. After that, you copied into that same place fresh startup
files from a special repair directory. When you reboot, Windows will
look for those files where it always does, and there won't be a stinker
in the bunch. The only thing is, there won't be all your settings for
all those applications you run every day, either. But not to worry.
Right now, you're sitting in something like a lifeboat -- it's not the
original ship, but it'll get you back to where you need to go. We'll get
everything back to that comfortable place, but only after we go through
the next steps.
Now type Exit and watch your computer restart into Windows XP again. Be sure not to tell it to boot from the CD this time. But
wait. That's not the way you had XP set up before this disaster struck!
That's OK. We're in a lifeboat right now -- this isn't your comfy
cruise ship, not just yet. Hang in there. I'm going to show you how to
restore your system to the way it was the moment before you told it to
install that errant application, or whatever it was you did, so follow
along and we'll go to the next step.
Here's where you'll
copy the saved registry files from their backed up location by using
System Restore. This folder is not available in Recovery Console and is
normally not visible -- Microsoft is protecting you from yourself by
hiding it from you and locking it away from you. But we have the keys.
Before you start this procedure, you'll need to change several settings
to make that folder visible:
1. Start Windows Explorer.
2. On the Tools menu, click Folder options.
3. Click the View tab.
4.
Under Hidden files and folders, click to select Show hidden files and
folders, and then click to clear the "Hide protected operating system
files (Recommended)" check box.
5. Click Yes when the dialog box is displayed that confirms that you want to display these files.
6.
Double-click the drive where you installed Windows XP to get a list of
the folders. It's important to click the correct drive.
7. Open the System Volume Information folder.
This folder appears dimmed because it is set as a super-hidden folder.
If you're using the FAT32 file system, this will be easy. If you're
using NTFS, it won't let you open the folder, but here's how to get
around that: Right-click on that system volume information folder and
select Sharing and Security. Then click the Security tab. (No security
tab? Skip two paragraphs.) Click Add, and then in the box that's labeled
"Enter the object names to select," type the name of the user that's at
the top of the Start menu -- that's probably you. [Damn it, why do they
say object names when it's people's names? I guess that's Microsoft for
you.]
Anyway, make sure you type the name the way it's
listed there on the Start Menu. I made the mistake of typing my first
name only and it wouldn't let me in. Type first and last name if that's
how it's written on the top of the Start menu. After you've typed that
in, click OK a couple of times and finally that monster will let you in.
But
what if you don't see a Security tab? Try this: Click to select the
checkboxes in the "Network sharing and security" area -- one is labeled
"Share this folder on the network" and the other is labeled "Allow
network users to change my files." Change the share name to something
short, like sysinfo. Then it'll let you in. After you're done with this
entire rescue operation, you might want to go back and change these back
to the way they were before, for maximum security.
OK.
Now here you are, in the inner sanctum where only the high priests go.
Be not afraid, all ye who enter here. As Microsoft so eloquently puts
it:
NOTE : This folder contains one or more _restore {GUID} folders such as "_restore{87BD3667-3246-476B-923F-F86E30B3E7F8}".
8.
Open a folder that was not created at the current time. You may have to
click Details on the View menu to see when these folders were created. There may be one or more folders starting with "RP x under this folder. These are restore points.
9. Open one of these folders to locate a Snapshot subfolder; the following path is an example of a folder path to the Snapshot folder:
C:\System Volume Information\_restore{D86480E3-73EF-47BC-A0EB-A81BE6EE3ED8}RP1Snapshot
From
the Snapshot folder, copy the following files to the C:\Windows\Tmp
folder (you can use your mouse, you're in Windows now, remember?):
_registry_user_.default
_registry_machine_security
_registry_machine_software
_registry_machine_system
_registry_machine_sam
This
is how Microsoft explains this: "These files are the backed up registry
files from System Restore. Because you used the registry file created
by Setup, this registry does not know that these restore points exist
and are available. A new folder is created with a new GUID under System
Volume Information and a restore point is created that includes a copy
of the registry files that were copied during part one. This is why it
is important not to use the most current folder, especially if the time
stamp on the folder is the same as the current time."
Anyway,
you're still not done. Don't worry, the magic is about to begin.
Believe me, if you do this in front of your friends, they'll start
thinking you're some kind of god. So, heavenly father, get ready to
dazzle 'em.
Now it's time to place those files you just
made visible to the Recovery Console where they belong. And to do that,
we need to get back into the Recovery Console.
So, make sure
your CD is in the drive, and restart Windows, this time hitting any key
when it tells you to do that if you want to boot from CD.
Don’t forget to press F6 if you have Raid Driver and load the Raid Driver.
Yes, you want to boot from CD, so you can launch your old cryptic pal, the Recovery Console.
Type R after it goes through that file-reading routine
that looks like an install but isn't. Then you're back into our
dark-suited friend with its ominous command line. It's kinda like going
into the basement to fix some broken pipe or something. But we're not
scared. The command line is our flashlight and friend. Here we go:
In
this part, you delete the existing registry files, and then copy the
System Restore Registry files to the C:\Windows\System32\Config folder:
From within Recovery Console, type the following commands:
Del c:\windows\system32\config\sam
Del c:\windows\system32\config\security
Del c:\windows\system32\config\software
Del c:\windows\system32\config\default
Del c:\windows\system32\config\system
copy c:\windows\tmp\_registry_machine_software c:\windows\system32\config\software
copy c:\windows\tmp\_registry_machine_system c:\windows\system32\config\system
copy c:\windows\tmp\_registry_machine_sam c:\windows\system32\config\sam
copy c:\windows\tmp\_registry_machine_security c:\windows\system32\config\security
copy c:\windows\tmp\_registry_user_.default c:\windows\system32\config\default
Now. You're done!
Type exit and your computer will reboot into whichever restore file you chose. Make sure you don’t boot to the CD.
But wait. If it's not the right one, that's OK, you can now go into
your System Restore area and pick a different restore point if you want.
There's a whole calendar full of them in there. I bet you didn't know
that Windows XP is watching just about every move you make, taking notes
all the while. It can restore about any state you had on that machine.
And the best part is, even when it's doing all that, it's still 10%
faster than Windows 2000 according to our extensive tests here at the
Midwest Test Facility. Here's how to get into that restore area if
you're not happy with the current restore point:
1. Click Start, then click All Programs.
2. Click Accessories, and then click System Tools.
3. Click System Restore, and then click Restore to a previous Restore Point.
Sheesh,
before this I hated the command line. Many of you probably still do.
But when it saves your butt like this, you have to feel grateful. I
should send out a badge of courage for all you intrepid souls who
followed me into these dark gallows, the basement of Windows XP. I hope
this routine was successful in bringing your computer back to life. I
know how it feels to have your computer down for the count. As a wise
old man once told me, "When your computer crashes, it's like your dog
just died." He was so right.
Note: I don't know who to give credit to for this information, Just thought I would pass it on.
Windows Defender
Windows Defender is a free program offered by Microsoft. The purpose of
this program is to keep your computer safe from spyware. Follow these
steps to adding Windows defender to your computer.
Step 1. Go to the Microsoft web site at www.microsoft.com/downloads.
Step 2. You should be in the Microsoft Download Center. Find the search bar that
says Bing. Type Windows Defender in the search bar.
Step 3. Now some links should have showed up. Click the link that says Windows
Defender link, should be the first one.
Step 4. Now you should see the download button. Click That button.
Step 5. Once the download is complete follow the instructions to install the
program.
Microsoft Internet Explorer Pop-Up Blocker
Windows Internet Explorer has a built in Pop-Up Blocker. A Pop-Up
Blocker is a program that is used to block them annoying pop-up
advertisements that some web sites have. Here are the steps to make sure
you Pop-Up Blocker is activated.
Step 1. Open your Windows Internet Browser.
Step 2. Once your Browser is open, look for the tools option at the top of your page.
Click that option.
Step 3. You will now notice that a pop down window appears. Move your mouse
down to the option that says Pop-Up Blocker.
Step 4. A window should open for the Pop-Up Blocker, now if one of the options
says click to turn on your Pop-Up Blocker push that. If the option says to
click to turn off your Pop-Up Blocker then your Blocker is running.
Step 5. If you wish you can use the other option and set your own setting for how
the Pop-Up Blocker works.
